|
|
General Industrial & Engineering Products
|
Suppliers Directory
|
Impetus Incorporated
| | Address : |
K 56/4 Sri Krishna Apartments Anna Nagar East |
| Telephone : |
044 6260946. |
| Fax : |
91 44 6268707. |
| Send : |
On-Line Trade Inquiry |
| |
|
Products |
|
Particle Size Analyser - Laboratory and measurement systems from Impetus Incorporated for production and analysis of fine powders manufactured by Hosokawa Alpine AG & Co OHG, Germany, an ISO 9001 company, with over 100 years experience in the field of powder processing systems. Alpine"s Model 200 LS N particle size analyser comes with an automatic weighing and print out facility combined with a software to link to a PC and this particle size analyser is effective for all powders from 30 microns to 1 mm is used in over 40,000 locations worldwide and some 50 in India, for accurate reliable use in analysis of powders. The company also offers on line particle size analyser, a joint development by Malvern Dry Laser Analyser for monitoring powder particle sizes from the production line and an Alpine Control System which takes over the data from the laser analyser and automatically adjusts the mill/classifier to bring back the particle size to the required level, if any, when a variation takes place. This system ensures minimum loss of time and material, while retaining the pre set particle size in microns and is useful in the cement, pharma etc.
|
|
Particle Size Analyser - Model 200 LS - Alpine Model 200 LS-N particle size analyser comes from Hosokawa Alpine AG, Germany useful for handling fine powders from 10 to 1,000 microns to find 200 LS-N useful for laboratory analysis and quality control. The equipment is fitted with a built-in computer, which can also be connected to a printer. The results obtained by the 200 LS-N are fast, accurate and reproducible and is importable under OGL.
|
|
ALPINE SPIRAL JET MILL - AN EXTREMELY COMPACT SPIRAL JET MILL, MODEL 50-AS, DEVELOPED BY HOSOKAWA ALPINE AG, GERMANY, IS AVAILABLE FROM IMPETUS INCORPORATED. THIS ENABLE MICRONISING EVEN BATCHES AS LOW AS 3 GM, WITH MINIMUM LOSS. THIS IS DESIGNED FOR THE ULTRAFINE SIZE REDUCTION OFDRY MATERIALS WITH A CRYTALLINE STRUCTURE UP TO A MOH'S HARDNESS OF 3. MICRONISED PARTICLE SIZES IN THE RANGE OF 0.5 TO 30 MICRONS CAN BE ACHIEVED. THE 50-AS CAN BE UTILISED FOR A WIDE RAGE OF PHARMACEUTICAL MATERIALS INCLUDING PARENTERALS, DPI (DRY POWDER INHALANTS), AND OTHER ACTIVE INGREDIENTS. SMALL BATCHES TOO, ARE PROCESSSED WITH HIGH EFFICIENCY. SOME OF ITS SPECIAL FEATURES ARE; JUST 50 MM (2") DIA, TABLE-TOP MODEL; STANDING ON A TRIPOD, VERRY EASY TO USE/CLEAN; REQUIRES ONLY COMPRESSED AIR (NO ELECTRICITY); MONOBLOC DESIGN, WELDS, CREVICES JIONT, DEAD ENDS; HIGH YIELD >99%, IDEAL FOR MICRO BATCHES MIN.3 GM; SURFACE FINISH RA <0.8 MICRONS OR BETTER; SPECIAL FILTER BAGS/OTHER OPTIONS ON DEMAND; AND PARTICLE SIZES OF 0.5 TO 30 MICRONS POSSIBLE.
|
|
PARTICLE SIZE ANALYSER - PRESENTING LABORATORY AND MEASUREMENT SYSTEMS FOR PRODUCTION AND ANALYSIS OF FINE POWDERS FROM IMPETUS INCROPORATED. THESE ARE MANUFACTURED BY HOSOKAWA ALPINE AG & CO OHG, GERMANY, AN ISO 9001 COMPANY, WITH OVER 100 YEARS EXPERIENCE IN THE FIELD OF POWDER PROCESSING SYSTMS. ALPINE'S MODEL 200 LS-N PARTICLE SIZE ANALYSER COMES WITH AN AUTOMATIC WEIGHING AND PRINT-OUT FACILITY AND A SOFTWARE TO LINK TO A PC. THIS STURDY AND ACCURATE PARTICLE SIZE ANALYSER FOR ALL POWDERS FROM 30 MICRONS TO 1 MM IS USED IN OVER 40,000 LOCATIONS WORLDWIDE AND SOME 50 IN INDIA, FOR ACCURATE RELIABLE USE IN ANALYSIS OF POWDERS. AN ALPINE 200 LS-N PRINT-OUT IS EQUALLY ACCEPTABLE TO THE BUYER AND SELLER OF POWDERS - A SOLUTION TO THE DISPUTES ARISING BETWEEN THEM, ALSO INTER-DEPARTMENTAL SUPPLY OF POWDERS IN BIG ESTABLISHMENTS. ALSO AVAILABLE IS AN ON-LINE PARTICLE SIZE ANALYSER, A JOINT DEVELOPMENT BY MALVERN DRY LASER ANALYSER FOR MONITORING POWDER PARTICLE SIZES FROM THE PRODUCTION LINE AND AN ALPINE CONTROL SYSTEM WHICH TAKES OVER THE DATA FROM THE LASR ANALYSER AND AUTOMATICALLY ADJUSTS THE MILL/CLASSIFIER TO BRING BACK THE PARTICLE SIZE TO THE REQUIRED LEVEL, IF ANY, WHEN A VARIATION TAKES PLACE. THIS SYSTEM ENSURES THAT WITH THE MINIMUM LOSS
|
|
FINE CUTTING MILLS - IMPETUS INCORPORATED PRESENTS FINE CUTTING MILLS FOR PLASTICS, MANUFACTURED BY HOSOKAWA ALPINE AG & CO, GERMANY. THESE FINE CUTTING MILLS ARE DESIGNED TO PRODUCE FREE-FLOWING, HIGH-QUALITY PLASTIC POWDERS WHICH HAVE OUTSTANDING DOWNSTEAMS PROCESSING QUALITIES. LDPE, LLDPE, HDPE, H-PVC PLASTICS, POLYMIDES, RUBBER, ETC, CAN BE PULVERISED TO CLOSELY DEFINED PARTICLE SIZE DISTRIBUTION, WITH LOW ENERGY CONSUMPTION AND AT AMBIENT TEMPERATURE WITHOUT COOLING MEDIA, SUCH AS CRYOGENIC GAS. THE FINE CUTTING MILLS PULVERISE PLASTIC GRANULES OF PIPES, SECTIONS AND EXTRUDED MATERIAL, JUST AS VIRGIN MATERIAL. THE END-FINENESS OF THE PLASTIC POWDER IS DEPENDENT ON THE SHAPE OF THE TEETH ON THE GRINDING DISCS, THE SPEED AND THE GRINDING GAP. DISTANCE BETWEEN THE TWO GRINDING DISCS CAN BE EASILY ADJUSTED AND MEASURED FROM OUTSIDE THE MACHINE EVEN IN CLOSED POSITION. WATER AND AIR CAN BE INTRODUCED INTO THE GRINDING CHAMBER, VIA A TWO COMPONENT NOZZLE TO KEEP THE ENTIRE GRINDING PROCESS COOL.
|
| |
|
View More Supplier Pages
Page(s) : 1 •
2 •
3 •
4 •
5 •
| |
|
|
|
